Owatrol Teak Olje – Teak Oil

Description

Owatrol Teak Olje is a blend of Owatrol Oil and high-quality teak oil designed for use on Teak and other exotic hardwoods. Protecting and enhancing the natural beauty of the wood, Teak Olje is a deep penetrating, clear oil that gives a rich warm appearance to any treated wood surface. Owatrol Teak Olje replaces the natural oils lost by exterior wood in the weathering process and will not blacken when exposed to UV rays making it ideal for garden furniture.

As a saturating oil, Owatrol Teak Olje protects and nourishes the wood from within its pores rather than forming a film on the surface which means that it will not peel or flake. It is easy to maintain with no sanding or stripping required and gives a rich, matt finish. Suitable for both interior and exterior wood.

Preparation

• Surfaces must first be thoroughly clean, dry and free of dirt, grease, grime, mildew and previous coatings.
• Treat any mildew with a 50/50 bleach/water solution. Scrub the solution onto the surface and leave it to stand for 10-15 minutes before rinsing thoroughly.
• After stripping and cleaning allow 2-3 days for the wood to fully dry out before applying the finish.
• Teak-Olje may only be applied to bare wood surfaces or a wood surface previously finished with Teak-Olje. ALL other finishes must be completely and thoroughly removed. If necessary sand the surface after cleaning and/or stripping (80 grit paper).

Application

Apply 2 even applications of Teak-Olje, ‘wet-on-wet’. To do this, first apply the initial coat and allow it to penetrate (normally 15-30 minutes). At this point apply the second coat and allow this to penetrate. If necessary, apply more coats following the same process until the wood is ‘saturated’ and will take no more oil.

Do not allow the Teak-Olje to become touch dry between applications, work in sections for larger projects to ensure this. Brush out or wipe up any excess Teak-Olje with a lint-free cloth 15-20 minutes after the last application to avoid shiny spots.

Note: Teak-Olje is not a surface coating, its place is in the wood and not on the surface. Teak-Olje protects by penetrating the wood, providing a rich, matt finish.

Maintenance

• Teak-Olje will gradually lighten over time due to exposure to the sun and UV rays.
• When the wood has taken on an un-oiled appearance or has lightened to a light grey colour, it is time for a maintenance application.
• Clean the surface with Net-Trol and allow it to fully dry.
• Then apply Teak-Olje wet-on-wet until the wood is saturated and the finish restored, usually, 1 or 2 applications will be sufficient.

Clean Up

• Clean all tools and equipment with white spirits while still wet.
• If the product has dried use paint stripper to remove it.
• Any rags, steel wool etc soaked in Teak-Olje may spontaneously catch fire if improperly discarded.
• Rags, steel wool etc. must be saturated with water after use or placed in a sealed, water-filled metal container, before disposing with household waste.

Restrictions

The tannins and natural oils in woods such as Keruing, Iroko and Padouk impede the penetration and drying of finishes. These species of wood should be thoroughly prepared or allowed to weather for 12 months before applying Teak-Olje. Contact us for preparation advice.

Things to Remember

• Use as is, do not thin.
• Shake or stir can thoroughly before application.
• Cover everything you do not wish to coat, including plants and shrubs.
• Apply between 5°C and 35°C.
• Do not apply if cold and/or wet weather is expected within 24 hours.
• Always work the entire length of the piece of wood being oiled to a logical break.
• Vertical surfaces should be coated from top to bottom.
• Never stop application in the middle of a piece of wood.
• Never apply in direct sunlight or to hot surfaces.
• Do not allow to dry between coats – apply Teak-Olje ‘wet on wet’.
• After spray application, always back-brush or back-roll to improve penetration and uniformity of coverage.